<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: Cisco IP SLA Sensor

The Cisco IP SLA sensor monitors Voice over IP (VoIP) network parameters using IP service level agreements (SLA) from Cisco via the Simple Network Management Protocol (SNMP).

Cisco IP SLA Sensor

Cisco IP SLA Sensor

i_square_cyanFor a detailed list and descriptions of the channels that this sensor can show, see section Channel List.

Sensor in Other Languages

  • Dutch: Cisco IP SLA
  • French: Cisco IP SLA
  • German: Cisco IP SLA
  • Japanese: Cisco IP SLA
  • Portuguese: Cisco IP SLA
  • Russian: Cisco IP SLA
  • Simplified Chinese: Cisco IP SLA
  • Spanish: Cisco IP SLA

Remarks

  • This sensor only supports IPv4.
  • This sensor has a low performance impact.
  • This sensor uses lookups to determine the status values of one or more channels.
  • If the object identifiers (OID) that this sensor uses are not available on the target device, the sensor shows the error message: No such object (SNMP error # 222). If this occurs, open the SNMP Compatibility Options setting of the parent device or group and set the Request Mode to Use single get.
  • If there is a very large number of IP SLAs available during sensor creation, we recommend that you limit the result set by using the Start Interface Index and End Interface Index options in the SNMP Compatibility Options setting of the parent device or group.

Basic Sensor Settings

Basic Sensor Settings

Basic Sensor Settings

Setting

Description

Sensor Name

Enter a name to identify the sensor. By default, PRTG shows this name in the device tree, as well as in alarms, logs, notifications, reports, maps, libraries, and tickets.

i_round_blueIf the name contains angle brackets (<>), PRTG replaces them with braces ({}) for security reasons. For more information, see the Knowledge Base: What security features does PRTG include?

Parent Tags

The tags that the sensor inherits from its parent device, parent group, and parent probe.

i_round_blueThis setting is for your information only. You cannot change it.

Tags

Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited.

i_round_blueIt is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>).

i_round_blueFor performance reasons, it can take some minutes until you can filter for new tags that you added.

The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:

  • ipslasensor

Priority

Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority (i_priority_1) to the highest priority (i_priority_5).

IP SLA Specific

IP SLA Specific

IP SLA Specific

Setting

Description

ID

The ID of the SLA that this sensor monitors.

This sensor can support the following operations with the specified type IDs:

  • echo (1)
  • pathEcho (2)
  • fileIO (3)
  • script (4)
  • udpEcho (5)
  • tcpConnect (6)
  • http (7)
  • dns (8)
  • jitter (9)
  • dlsw (10)
  • dhcp (11)
  • ftp (12)
  • icmp-jitter (16)
  • path-jitter (23)

i_round_blueThe numbers are the IDs of the SLA types as reported by the target device. PRTG translates them into the corresponding strings. These IDs are independent of the IDs that you see in the Add Sensor dialog. If the target device returns other values, this sensor shows an error message that says that it cannot find the type.

i_round_bluePacket Loss values are summarized but have no explicit channel for Source-Destination or Destination-Source values.

Type

The type of the SLA that this sensor monitors.

Name (Tag)

The name of the SLA that this sensor monitors.

Owner

The owner of the SLA that this sensor monitors.

Frequency

The frequency of the SLA that this sensor monitors.

Sensor Display

Sensor Display

Sensor Display

Setting

Description

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.

i_round_blueYou can set a different primary channel later by clicking b_channel_primary below a channel gauge on the sensor's Overview tab.

Graph Type

Define how different channels are shown for this sensor:

  • Show channels independently (default): Show a graph for each channel.
  • Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
    i_round_redYou cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Inherited Settings

By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click b_inherited_enabled under the corresponding setting name to disable the inheritance and to display its options.

i_square_cyanFor more information, see section Inheritance of Settings.

Scanning Interval

Scanning Interval

Scanning Interval

i_square_cyanFor more information, see section Root Group Settings, section Scanning Interval.

Schedules, Dependencies, and Maintenance Window

i_round_blueYou cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional schedules, dependencies, and maintenance windows. They are active at the same time as the parent objects' settings.

Schedules, Dependencies, and Maintenance Window

Schedules, Dependencies, and Maintenance Window

i_square_cyanFor more information, see section Root Group Settings, section Schedules, Dependencies, and Maintenance Window.

Access Rights

Access Rights

Access Rights

i_square_cyanFor more information, see section Root Group Settings, section Access Rights.

Channel List

i_round_blueWhich channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.

Channel

Description

Avg. Jitter

The average jitter

Avg. Jitter Destination - Source

The average jitter between destination and source

Avg. Jitter Source - Destination

The average jitter between source and destination

Avg. Latency Destination - Source

The average latency between destination and source

Avg. Latency Source - Destination

The average latency between source and destination

Average Round Trip Time (RTT)

The average RTT

i_round_blueThis channel is the primary channel by default.

Downtime

In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status

ICPIF

The ICPIF

Late Packets

The number of late packets

Max. Latency Destination - Source

The maximum latency between destination and source

Max. Latency Source - Destination

The maximum latency between source and destination

Max. RTT

The maximum RTT

Min. Latency Destination - Source

The minimum latency between destination and source

Min. Latency Source - Destination

The minimum latency between source and destination

Min. RTT

The minimum RTT

MOS

The MOS

Packets Lost

The number of lost packets

Packets Lost %

The number of lost packets (%)

Packets Out of Sequence

The number of out-of-sequence packets

More

i_square_blueKNOWLEDGE BASE

What security features does PRTG include?